Mojones915
Well-Known Member
- Joined
- May 16, 2018
- Location
- Saxapahaw
Thinking of selling my K5 project, not been able to give it any attention lately and could use the funds for the race jeep.
Build Thread Here:
1 ton K5 - now with even more mischief and bad decisions
1991 K5 blazer, 350, 700R, NP241 with SYE and new rear drive shaft
CUCV dana 60 front, open, new lugnut 4x4 3/4 ton disc brakes, barnes diff cover
CUCV 14 bolt rear, gov lock, Lugnut 4x4 disk brake conversion, barnes shave kit and diff cover
Front suspension is DIY4X B52 brackets, new springs, new Bilstein shocks
Rear suspension is 63in new springs with DIY4X brackets, have new bilstein shocks that are not mounted
New PSC steering box ported for hydro assist, ORD crossover steering, bilstein steering stabilizer
H1 rims recentered with rock rings, 37in Goodyear MTRs
Custom front/ rear bumpers
Has rust in rockers (have replacements), driver and rear passenger footwell
Planning to pull the winch off to use on my trailer
Have a bunch of random parts, trim, truck tailgate etc to go with it.
Battery is currently dead, Haven't tried to jump it off in while but will work on it this weekend. It ran and drove on the trailer a few months ago when we moved back to Kernersville. Would probably want to trailer it until it can be gone over and given a tune up.
Firm at $10k, don't really want to get rid of it but hate to see it sit and waste away due to other projects. Have the title for it. Located in Kernersville
I have a 5.3LS I pulled to swap into it if buyer is interested in that as well and a ton of other parts originally destined for this that could be negotiated for additional, if not they will end up in the parts section
Holley terminatorX and digital pro dash
ORD engine crossmember and brackets for LS swap to make it bolt in
Full width trusses for both axles
Truck tail gate and hardware
4 H2 wheels
Set of used mastercraft reclining suspension seats
Build Thread Here:
1 ton K5 - now with even more mischief and bad decisions
1991 K5 blazer, 350, 700R, NP241 with SYE and new rear drive shaft
CUCV dana 60 front, open, new lugnut 4x4 3/4 ton disc brakes, barnes diff cover
CUCV 14 bolt rear, gov lock, Lugnut 4x4 disk brake conversion, barnes shave kit and diff cover
Front suspension is DIY4X B52 brackets, new springs, new Bilstein shocks
Rear suspension is 63in new springs with DIY4X brackets, have new bilstein shocks that are not mounted
New PSC steering box ported for hydro assist, ORD crossover steering, bilstein steering stabilizer
H1 rims recentered with rock rings, 37in Goodyear MTRs
Custom front/ rear bumpers
Has rust in rockers (have replacements), driver and rear passenger footwell
Planning to pull the winch off to use on my trailer
Have a bunch of random parts, trim, truck tailgate etc to go with it.
Battery is currently dead, Haven't tried to jump it off in while but will work on it this weekend. It ran and drove on the trailer a few months ago when we moved back to Kernersville. Would probably want to trailer it until it can be gone over and given a tune up.
Firm at $10k, don't really want to get rid of it but hate to see it sit and waste away due to other projects. Have the title for it. Located in Kernersville
I have a 5.3LS I pulled to swap into it if buyer is interested in that as well and a ton of other parts originally destined for this that could be negotiated for additional, if not they will end up in the parts section
Holley terminatorX and digital pro dash
ORD engine crossmember and brackets for LS swap to make it bolt in
Full width trusses for both axles
Truck tail gate and hardware
4 H2 wheels
Set of used mastercraft reclining suspension seats
Last edited: