Front LEDs in a TJ

[burrellsjeep]

What are you guys running for front led turn signals under the head lites (like the look of a CJ). Been looking and all I can find is "clearance marker" leds, I looking for a round flush mount, The clearance leds are just two wire, so on and off, Shouldn't the light be wired, Running, Turn, and off. so three wire? Or would it be ok to have just on and off, IE it would turn off and on to signal a turn instead of getting brighter, oh course this only would matter at night.

 

[1badz2nv]

Try these,

http://www.ledselect.com/LED-turnsignallamps.htm

 

[81K5GUY]

been looking at doing jk front turnsignals when I put on the tube fenders and these look pretty slick

http://www.4x4led.com/cm/cm_jk.htm

 

[Airdoc]

I saw a write-up on that the JK marker/turnsignals are "plug and play" with the TJ connector - so no wiring changes at all (retains 3 wire OE set-up) - just cut a hole.

 

[81K5GUY]

yep they are plug and play,heres a write up on the install. Its mixed in with the abs fender writeup about halfway down the page.

http://www.jeepforum.com/forum/f9/new-lightweight-classic-cj-style-flattie-fenders-wrangler-959981/

 

[burrellsjeep]

Thanks,

Gonna check these out.

 

[burrellsjeep]

been looking at doing jk front turnsignals when I put on the tube fenders and these look pretty slick
http://www.4x4led.com/cm/cm_jk.htm

Still listing these as "marker lights", and kinda steep too $90 a pair.

 

[81K5GUY]

I will probally go with the stock jk lights which are alot cheaper .I think the reason those are so steep are that they are smked and they are leds.

 

[81K5GUY]

quoted from the write up these arent as bad

The JK turn signal enclosures I used came from www.rockauto.com/ & their part numbers are 023120L (023-120L) & 023120R (023-120R). They are $18.05 each plus shipping.

also they serve 2 purposes on the jk signal/marker

 

[burrellsjeep]

Try these,

http://www.ledselect.com/LED-turnsignallamps.htm

Thanks but I was looking for something in the 2'' range, I can find them in 4'' but, I think that would be kinda big

 

[burrellsjeep]

quoted from the write up these arent as bad
The JK turn signal enclosures I used came from www.rockauto.com/ & their part numbers are 023120L (023-120L) & 023120R (023-120R). They are $18.05 each plus shipping.
also they serve 2 purposes on the jk signal/marker

Yeah that might be route I go.

 

[81K5GUY]

heres a little better write up on the light install itself

http://www.jeepforum.com/forum/f9/turn-signal-relocation-418647/

 

[81K5GUY]

heres a pic ith 2" leds

I can find out where he got them if youre interested

 

[burrellsjeep]

heres a pic ith 2" leds

I can find out where he got them if youre interested

Pretty Sure those are the marker style leds, I think some guys are just running them like that.

 

[Airdoc]

heres a little better write up on the light install itself
http://www.jeepforum.com/forum/f9/turn-signal-relocation-418647/

This is the write-up / install I liked better...I'm not much into trying to file exact notches in the sheet metal to match the OE JK index on the light.

I'd rather file/sand down the plastic index tabs on the light itself....but this is just thinking out loud.

 

[81K5GUY]

finally got around to installing the jk lights a while back

 

[burrellsjeep]

Did Mine also, Those JK signals are the way to go.