White Rock (Toyota)

It will run better if you take the Bush sticker off.
 
i should take that off and the POWMIA stickers and turn in my right to bare arms too... right?
 
I was just agarvating you. Do as you wish.
 
Jeff had a bad experience with a bush once. Now he's:gay:
 
any heads ups or suggestions are welcome.
 
yea i was thinking about finding a head and working it. port and polish,cams, headers. not too worried about power though. i cant have anything fast with my driving record haha. thats why i sold my BMW.
 
LC makes some rowdy stuff.....but it's high dollar. You can do a 4.3 swap and come out cheaper than build a toyota race motor and still have the same power.
 
yea lc is very expensive. for now im just going to do cheap tube headers cause every gasket on my man leaks. should give me a little more umf
 
went to see Chase at EastCoastGearSupply today and as always he was a big help and had almost a whole SAS kit in stock!
overnighted the stuff he didnt have. HOPEFULLY White Rock will go under the knife this weekend,be put back on all 4s and off the road :Rockon::Rockon::Rockon::Rockon:
 
got all my parts today minus fj60 rotors ad wheel spacers,and got the axle back together half way. i will try and get some pics tommorow, i have been rushing so much to get it ready for the swap this weekend i have been forgetting to take pics.

heres whats on the menu:
1980 front axle replaced seals and bearings
63" chevy springs
TG rear leaf brackets
TG front spring hanger
TG front shakles and frame tubes
TG hi-steer
TG u-bolt flip kit
TG shock hoops
stainless brake lines


i think the only things i need to get tomorrow before she goes under the knife is fj60 rotors and wheel spacers
 
Got the Ifs cut off and the axle mocked up in the front today. Should be Rollin on all fours tomorrow after about six hours more labor. I would post pics but I am sending this from my phone and it's 1:40am.
 
well we put it on all 4's and i drove it up on the trailer. i have allot of little things left then :driver: cant wait to do some flexin
 
click link above. new photos again with some flex /\
 
ITS ON THE ROAD!!!!

well i got some add a leafs from my local 4WheelParts and a pair of shocks. they where very helpful and knowledgeable. and i :driver: it home!!!!!! WOO WOO!!!!!

needs a little bit of test and tune but all and all its going,stopping, and flexing. so im :bounce2:

still need to:
relocate rear shocks
adj pin angle
make stronger rear shakles
make frnt drive shaft
annnnnd thats about it for now.
 
Very nice, looks good. But one warning, I would gusset the crap out of those front shock hoops since you didn't plate the frame. My brother and I built some exactly like that and after a full day of ridiculously bumpy roads in Mt. City the hoops tore right out of the frame. Made two perfect little holes
 
thanks for the heads up. i know i need to do it. im pretty sure some came with the set i just gotta get them. if not i will make them. did you run one to the top of the frame and the other to the top of the engine mount box thingy?
 
i welded in the gussets today.
another thanks to EastCoastGearSupply
 
got my front drive shaft built today and went wheelin! YAY!:driver:

it was to dark and raining to take pics but i will go again tomorrow hopefully with day light. so far so good
 
ai45.photobucket.com_albums_f89_mudslinginyota_Trucks_DSC_0274.jpg

ai45.photobucket.com_albums_f89_mudslinginyota_Trucks_DSC_0277.jpg


bigger tires,lower gears,lockers,longer shocks,and more power... to come
 
Back
Top