FB MP finds of the day.

Guy on a 1st gen FB group just bought this. Didn't disclose what he paid

Log into Facebook

Log into Facebook to start sharing and connecting with your friends, family, and people you know.
www.facebook.com www.facebook.com

Probably among the nicest low mile models out there
 
RatLabGuy said:
Guy on a 1st gen FB group just bought this. Didn't disclose what he paid

Log into Facebook

Log into Facebook to start sharing and connecting with your friends, family, and people you know.
www.facebook.com www.facebook.com

Probably among the nicest low mile models out there
Click to expand...
I do think $15-20k would make sense for something like that. Hopefully the seller got $35k.
 
jeepinmatt said:
I do think $15-20k would make sense for something like that. Hopefully the seller got $35k.
Click to expand...
In the last few years these things have become quite the collector target and absolutely shot up in value. Clean ones go on BAT for 25k all the time. There's only a couple left in the country w/ that kind of mileage.
 
This looks like a deal. Mo better then @jeepinmatt ;) Built 2002 jeepTJ
$12,500$13,500

2002 TJ 468180071_433070179667573_895158497293923862_n.jpg


2002 jeep tj
140000 miles
Dynatrack full float hp 60’s ARB air lockers front and rear
New 37 maxxis razors on trail ready bead locks
Power premiere on board welder with 110 V plug
 ATLAS ll transfer case
Full traction long arm needs bushings replacement 
I have a Clayton stretch 4 link I can include for the right price and a ruff stuff 3 link front and psc hydro assist set up
Master craft seats
Rock hard bolt in roll cage
Many more things if sure I’m forgetting
Jeep runs and drive but has been sitting for a while it is not very road friendly at the moment but could be with some work

Log into Facebook

Log into Facebook to start sharing and connecting with your friends, family, and people you know.
www.facebook.com www.facebook.com
 
ghost said:
This looks like a deal. Mo better then @jeepinmatt ;) Built 2002 jeepTJ
$12,500$13,500

View attachment 429293

2002 jeep tj
140000 miles
Dynatrack full float hp 60’s ARB air lockers front and rear
New 37 maxxis razors on trail ready bead locks
Power premiere on board welder with 110 V plug
 ATLAS ll transfer case
Full traction long arm needs bushings replacement 
I have a Clayton stretch 4 link I can include for the right price and a ruff stuff 3 link front and psc hydro assist set up
Master craft seats
Rock hard bolt in roll cage
Many more things if sure I’m forgetting
Jeep runs and drive but has been sitting for a while it is not very road friendly at the moment but could be with some work

Log into Facebook

Log into Facebook to start sharing and connecting with your friends, family, and people you know.
www.facebook.com www.facebook.com
Click to expand...
:flipoff2:
Also stock motor and trans and a lot of rust in a lot of places. But hella nice running gear. Different target audience for sure.
 
jeepinmatt said:
:flipoff2:
Also stock motor and trans and a lot of rust in a lot of places. But hella nice running gear. Different target audience for sure.
Click to expand...
Yea Atlas Daynatrac axles with ARB's are worth the asking price I would think.
 
ghost said:
This looks like a deal. Mo better then @jeepinmatt ;) Built 2002 jeepTJ
$12,500$13,500

View attachment 429293

2002 jeep tj
140000 miles
Dynatrack full float hp 60’s ARB air lockers front and rear
New 37 maxxis razors on trail ready bead locks
Power premiere on board welder with 110 V plug
 ATLAS ll transfer case
Full traction long arm needs bushings replacement 
I have a Clayton stretch 4 link I can include for the right price and a ruff stuff 3 link front and psc hydro assist set up
Master craft seats
Rock hard bolt in roll cage
Many more things if sure I’m forgetting
Jeep runs and drive but has been sitting for a while it is not very road friendly at the moment but could be with some work

Log into Facebook

Log into Facebook to start sharing and connecting with your friends, family, and people you know.
www.facebook.com www.facebook.com
Click to expand...
That’s not a bad deal. A bit of elbow grease could get that thing nice
 
What kind of mill is this?

Log into Facebook

Log into Facebook to start sharing and connecting with your friends, family, and people you know.
www.facebook.com www.facebook.com
 
ghost said:
What kind of mill is this?

Log into Facebook

Log into Facebook to start sharing and connecting with your friends, family, and people you know.
www.facebook.com www.facebook.com
Click to expand...
One to stay away from most likely. That column doesn't look nearly beefy enough for metalwork. Plus any CNC retrofit that is not already well sorted is a complete basketcase waiting for you to throw time and money at it and never get any return.
 
Back
Top