Help Me Clear Various Crap Out Of Garage!

Mcamish01

Member
Joined
Jul 21, 2024
Location
AVL, NC
I have accumulated a rather large pile of take off stuff from the rig during the last overhaul and it needs to move out of my shop to a better home! Not trying to make a bunch of money, just don’t want to throw away/scrap some good useable gear. Will probably have the wife post some of it on the FB marketplace as well, as I’m not on the socials. All of the parts are located in Asheville, NC. Would rather not ship, but some of it might work. Could potentially also make it available in Greenville, SC by dropping at my folks house there. Shoot me email- bsudder@gmail.com, or call/text- 864-884-1212. I work three weeks on / three weeks off, so pick up may need to scheduled a little unless the wife can make it available.

Barclay
 
Ok, on to the junk…

Solid D60 diff cover with hardware. Nothing wrong with it, just had to go to a fab’d steel cover in order to integrate with my truss.

How’s $20 sound?

IMG_6361.jpeg
IMG_6360.jpeg
 
10 LB PowerTank CO2 Tank

I’ve run this setup for about 20 yrs now- works great! Had the tank re-certified probably 6 yrs ago, no issues. Slipped and fell into a fancy new ARB compressor, which packages better into the reduced space on the updated rig setup, so time to move this along. Works particularly well at reseating tires and running air tools.

$75.

IMG_6368.jpeg
IMG_6369.jpeg
IMG_6371.jpeg
IMG_6372.jpeg
 
Two Corbeau 3” 5 Point Harnesses with Camlocks. No cuts, frays, mildew, etc. Slightly faded from age (about 15 yrs old, so Definitely not SFI approved, but perfectly functional and safe). Camlocks work great (once I cleaned out the grease and replaced with dry lube). Can unpack and take better pictures when I get home if you’d like- just hit me up.

$20 for pair.

IMG_6392.jpeg
 
MSD Plug Wires for Dodge Magnum Series V8.

Bought these for my Dodge 5.9, prior to going to LS coil packs in order to simplify the integration of TerminatorX engine management. Never even installed. Would likely work for many typical distributor type applications.

$20.

IMG_6376.jpeg
IMG_6377.jpeg
IMG_6378.jpeg
 
Detroit Locker, Dana 60, 35 Spl, - $150
Ford 10” HP D60 5:38 Gear Set - $100 (standard old D60 style pinion, not the silly new fat/short SD60 style)
Yukon Chromoly D60 1350 Yoke - $30

Will separate. No issues when pulled, everything looks good. Going to Currie HP D70 35 spl gearset and 40 spline Detroit to hopefully buy some leeway to account for my fresh 408 stroker dodge v8 and occasional poor decisions. No bearings - pulled the old ones to make setup bearings for the new gears.

IMG_6365.jpeg
 
Derale Fluid Cooler - $35.

Used this as my trans cooler for my TF999 behind a healthy Dodge V8. Worked great for rec. wheeling and crawling- even for summer wheeling in the southwest. Only times it felt a little overwhelmed was high power playing in dunes when in High Range. When I overhauled the rig, I went back with the larger version of this cooler, as I wanted to be able to bomb Sand Hollow and Johnson Valley without worries. Would be great for lower hp rigs, or really any crawling, or probably any transmission with a bit more capacity than the tiny TF904/999.

IMG_6395.jpeg
IMG_6396.jpeg
IMG_6400.jpeg
IMG_6399.jpeg
IMG_6397.jpeg
 
Mishimoto Charge Air Cooler (Intercooler) - $35.

Used this initially as the intercooler for the R2.8 Cummins in my ‘76. Cherokee Chief, but it tended to heat soak pretty badly during steep mid speed (30-40 mph) mountain driving during the summer, so I went to a larger volume cooler to correct this problem. Good, well made unit, just not enough volume for my application.

IMG_6379.jpeg
IMG_6380.jpeg
IMG_6384.jpeg
IMG_6383.jpeg
IMG_6382.jpeg
IMG_6381.jpeg
 
Oil Cooler, off of Robinson R22 Helicopter, Lycoming 0-360 Powerplant - $35.

Ok, so this one’s a bit odd. This is a timed out (2000 hrs) oil cooler off of one of the helicopters from a company where I formerly worked. Aluminum, but heavy. An “absolute unit” as the kids say. Would work well as any type of fluid cooler, especially if paired with airflow/fan. No leaks, holds pressure fine, just has to be replaced by regulation. Wish I had a use for it, but just don’t, and need it gone before I MAKE a use for it.


IMG_6385.jpeg
IMG_6386.jpeg
IMG_6387.jpeg
IMG_6389.jpeg
IMG_6390.jpeg
IMG_6391.jpeg
 
IMG_5401.jpeg
IMG_5400.jpeg
IMG_5399.jpeg
IMG_5402.jpeg



Eibach 2.5” (for 2.0 CO’s) Coil Over Springs - $30 per pair.

(2) 16” x 300lb (red)

(2) 16” x 300lb (silver)

(2) 14” x 200lb (silver)

(2) 12” x 200lb (silver)

Few sets of springs from over the years, plus the last revision of the rig shed about 300lbs and changed geometry, so had to replace several to dial back in. Red set are a bit faded (just the paint, they’re all mechanically good). All have varying amounts of powder coat wear and chipping.

IMG_5405.jpeg
IMG_5406.jpeg
IMG_5403.jpeg
IMG_5404.jpeg
 
Ford Sterling 10.5” Hubs/Spindles -$20
Yukon Chromoly 35 spl Shafts for Sterling -$20

These came off my rear axle, as I’m going back with ‘05+ Ford unit bearing cups to match the front. Spindles should have about 1.5” to turn down and sleeve onto axle tubes. Hub bearings good, would probably want to replace seals, though. Drilled for 8x6.5, but easily returned to 8x170. Shafts work out to a WMS of about 67.25” on a D60. No brakes- had Spidertrax hats/rotors wilwood calipers, but they’re going on the new axle.

IMG_6373.jpeg
IMG_6374.jpeg
IMG_6362.jpeg
IMG_6364.jpeg
IMG_6363.jpeg
 
Big ‘Ol Bag of Lugnuts, 7/16 x 20, two full sets (24 ea.) - Free to Whoever Comes to Get Them.

One set (24) of open end, one set (24) closed end. Both conical, bulged end, for 3/4 socket IIRC. All in great shape. Didn’t care for the open end look, and got the closed. Then went to 1/2” studs when I put the chromos in the ‘Chief, and no other vehicles/trailers to use them on. Don’t make me scrap ‘em, please.
IMG_6393.jpeg




And that’s all for now. Thanks for looking!

Barclay
 
Ok, so looks like the 14” x 200lb spring and diff cover are pending, along with the Detroit.
 
I'll take the trans cooler if that falls through, Power tank if that deal falls through, seat belts, MSD wires, and the lug nuts. Can pick up any time this weekeend, Friday-Sunday, after that, it'll be next friday before I am free. I'm getting a toolbox from Jody, but it's not gonna be ready until next Friday or maybe after . Be nice to be able to make one trip up the MNT, unless you want these things picked up sooner
 
Back
Top