Random pic thread.

IMG_8823.jpeg
 
orange150 said:
It’s wild to think you can’t find anyone to work on a carb’d outboard.
Click to expand...
No you can't. I've been trying to get someone to work on my 85hp Johnson for 2 years now.
 
Found some bluebird eggs in an old fence post. Don't have the @Ron video surveillance on it though.

20250507_153541.jpg
 
skyhighZJ said:
Man, I’ve wanted to go for a long time. Report back if it’s as epic as the video clips are!!
Click to expand...
Will do. Pretty good time so far!

20250510_144004(0).jpg
 
Busy day.
Cut the metal roofing for the chicken coop to length. Tried to use a 24 tooth framing blade that had some use on it so as not to waste a good blade. That was a mistake. It ended up cutting crooked and leaving a rough edge. Finally said F it, if I have to ruin a 60 tooth finishing blade, so be it.
Here’s the 24 toothless
IMG_9536.jpeg
IMG_9532.jpeg
IMG_9534.jpeg


And the 60 tooth with a beautiful cut and not a single damaged tooth and a much nicer finish.
IMG_9537.jpeg
IMG_9533.jpeg
IMG_9535.jpeg


Then it was new toy time. :D
IMG_9540.jpeg
IMG_9542.jpeg


Already had the spot picked out, just needed to clean it up and move some junk. Happened to have a bunch of half height blocks that were perfect for this application.
IMG_9543.jpeg
IMG_9544.jpeg
IMG_9545.jpeg


Looking forward to the extra 8” capacity on width and more horsepower over my old mill. Eventually I’d like to add some hydraulic log handling capabilities to it, but this is a good start for now.
 
jeepinmatt said:
Busy day.
Cut the metal roofing for the chicken coop to length. Tried to use a 24 tooth framing blade that had some use on it so as not to waste a good blade. That was a mistake. It ended up cutting crooked and leaving a rough edge. Finally said F it, if I have to ruin a 60 tooth finishing blade, so be it.
Here’s the 24 toothless
View attachment 437987View attachment 437988View attachment 437989

And the 60 tooth with a beautiful cut and not a single damaged tooth and a much nicer finish.
View attachment 437990View attachment 437991View attachment 437992

Then it was new toy time. :D
View attachment 437982View attachment 437983

Already had the spot picked out, just needed to clean it up and move some junk. Happened to have a bunch of half height blocks that were perfect for this application.
View attachment 437984View attachment 437985View attachment 437986

Looking forward to the extra 8” capacity on width and more horsepower over my old mill. Eventually I’d like to add some hydraulic log handling capabilities to it, but this is a good start for now.
Click to expand...
Probably have been better off trying to wrestle a beaver with your thumb in his ass and have him chew through the metal.
 
skyhighZJ said:
Man, I’ve wanted to go for a long time. Report back if it’s as epic as the video clips are!!
Click to expand...
So, it was fun. Cheesy and ridiculous as it was, I still had a good time. It's not much of, what i would call, a baseball game. It's more entertainment with a few pitches thrown in there for good measure. They play music the entire time. Even when people are pitching/batting. Dances galore. Even had a nail biter at the very end. It's very kid friendly and honestly, kid focused, IMO. It's fun for a night.
 
jeepinmatt said:
Busy day.
Cut the metal roofing for the chicken coop to length. Tried to use a 24 tooth framing blade that had some use on it so as not to waste a good blade. That was a mistake. It ended up cutting crooked and leaving a rough edge. Finally said F it, if I have to ruin a 60 tooth finishing blade, so be it.
Here’s the 24 toothless
Click to expand...


You might be a carpenter after all.....always blame it on the blade :D.
 
McCracken said:
So, it was fun. Cheesy and ridiculous as it was, I still had a good time. It's not much of, what i would call, a baseball game. It's more entertainment with a few pitches thrown in there for good measure. They play music the entire time. Even when people are pitching/batting. Dances galore. Even had a nail biter at the very end. It's very kid friendly and honestly, kid focused, IMO. It's fun for a night.
Click to expand...

It's the Globetrotters on a baseball diamond. We tried to go when they were in Durham last year but tickets went quick.

Duane
 
Back
Top