Warrior Welding LLC shop.

Elderly man down the road heats with wood. He is out! Loading up as much as he needs with another neighbor who checked in on him.
 
tlucier said:
You’re a good man!
Click to expand...
Thanks, I was just part of the reaction. Another neighbor got the info. That neighbor knew we had the wood.
 
PXL_20251006_181416506.jpg

After we got the bumper and storage off. Those frame extensions are 3/4 plate btw.
PXL_20251112_202328826.MP.jpg

Little shave of all the really bad damage. Dollied the rest.
PXL_20251112_202323008.MP.jpg

Little trimming of a factory replacement. I've made them from scratch. Bump bending the radius sucks and takes about 70 locations at 1/4 spacing. Being both corners and the middle we ordered a skin. Took forever to come in.
PXL_20251112_202316000.MP.jpg

Trash!
PXL_20260210_194556345.jpg

Just needs the lettering and stripes.
 
skyhighZJ said:
Not to sound shitty but is there a reason this kind of damage happened? If driver error was there repercussions like wearing the dunce cap for a month or something??
Click to expand...
I've seen the fault swing both ways over the 18 or so years total I have worked on Emergency equipment. As far as penalties I couldn't tell you how that plays out. Most of the time we rarely get details on the faulty party let alone how the incident occurred. A career member would have better knowledge.

I have fixed numerous units over operator error.....the most of which are doors and equipment torn off leaving in a hurry. Quoted one of those just this week. Stainless body. Really messed up. Probably near 200 man hours not including paint. Fixed a few doors last year. Also have two more besides the recent quote in waiting. One we just delivered of our own brand/build last year. It left and tore the door post out of the concrete. Buckled the garage door. The best part is our product still shuts, didn't tear the door off and the cabinet is still square!

A lot of others are fubared by rubber neckers on the scene. Many years ago I cut the entire back corner off a steel bodies unit. Guy hit them on 321 at full highway speed. Never touched the brakes. He was DOA.

Fixed one that went through a fence. Top rail pinned the Captain to the passenger seat like a tooth pick in an olive.

Burnt, Rolled, And every corner I've replaced or rebuilt them.
 
I've always thought Sutphen engines were some sharp looking rides. Their aerials not so much though lol.

Duane
 
CLRracer said:
I've always thought Sutphen engines were some sharp looking rides. Their aerials not so much though lol.

Duane
Click to expand...
I had the pleasure of meeting old man Sutphen when I worked for a hydraulic cylinder manufacturer in Ohio. Dude in his 90s was nut and bolt restoring 1st gen rolls Royce’s doing all the work himself. He had 5 or 6 going at the same time

There was a story they told where he was trying to make a model t based hot rod using the engine from a fire truck. He apparently got so excited to drive it once it was running that he took off from the shop, and proceeded to circle the building about 10 times with the clutch in. Turns out he hadn’t done brake lines yet, and just let it coast to a stop. He was in his 80s at the time.

They have the only no weld ladders in the industry using specially made rivets for ladder assembly that make for a safer product supposedly
 
Shreddinlettuce said:
I had the pleasure of meeting old man Sutphen when I worked for a hydraulic cylinder manufacturer in Ohio. Dude in his 90s was nut and bolt restoring 1st gen rolls Royce’s doing all the work himself. He had 5 or 6 going at the same time

There was a story they told where he was trying to make a model t based hot rod using the engine from a fire truck. He apparently got so excited to drive it once it was running that he took off from the shop, and proceeded to circle the building about 10 times with the clutch in. Turns out he hadn’t done brake lines yet, and just let it coast to a stop. He was in his 80s at the time.

They have the only no weld ladders in the industry using specially made rivets for ladder assembly that make for a safer product supposedly
Click to expand...
They have a aircraft hanger full of awesome restored stuff, including a airplane.
As for the ladder the rivets are a Huck bolt. I have in the last year had to change out some damaged structural pieces in a ladder of that brand. Very modular. Not terrible and much easier to reinspect. Any repair on a fabricated welded unit goes under NDT testing. Annual test done over UL gets every single weld mag particle tested if steel. Visual on aluminum and if suspect Sonography. Every single bolt gets a torque wrench as well.
 
Back
Top