What have you done to your rig today?

[Chris_Keziah]

Adding to the 10 mpg club I see.

More like adding to the paid off vehicle club, but hoping it'll pull mid teens for mileage.

 

[NickMaul]

More like adding to the paid off vehicle club, but hoping it'll pull mid teens for mileage.

Freeing up that money for Dana 60s, a LS swap, and stickies I see


Sent from my iPhone using Tapatalk

 

[Stuntman Autoworks]

hoping it'll pull mid teens for mileage.

My grandpa has a 99 and if yours is 4wd also mid teens ain't going to happen.

 

[NickMaul]

My grandpa has a 99 and if yours is 4wd also mid teens ain't going to happen.

My WJ 4.0 barely gets mid teens lol


Sent from my iPhone using Tapatalk

 

[Bebop]

My WJ 4.0 barely gets mid teens lol
Sent from my iPhone using Tapatalk

Damn, I was getting 20/22 with my 4.7.

Right before it dropped a valve and a few minor catastrophic engine related issues...

 

[McCracken]

This finally came in the mail

 

[NCJeeplover]

My WJ 4.0 barely gets mid teens lol


Sent from my iPhone using Tapatalk

I've got a completely stock 2wd 4.0 zj that has gotten a best of 16mpg......I feel your pain.

 

[grapehead]

changed out the bad TPS in the 87 4runner, it runs like new now.

replaced the cracked exhaust manifold in the 98 xj, it's running much happier.

eagerly anticipating watching fuel mileage climb in both.

 

[jcramsey]

Pulled the plugs and turned over the engine in dads “new” c10...advertised with water in the oil pan. At least I know they weren’t lying

Stuck them back in and it fired right up. Hoping a new head gasket is all it takes to get him mobile.

 

[Keith1138]

Not my truck but my dads. Replaced the wheel bearing again, new calipers, pads and rotors. This time we used timken wheel bearings instead of drive works ones. Hopefully these last alot longer before the wheel speed sensor goes out. Dried concrete mud is worst than red clay.

Sent from my SM-G892A using Tapatalk

 

[scrubber3]

Rebuilt the rear brakes on the XJ

 

[nc_jk_crawler]

Forgot to post last weekend but the Prorock44 is just about back together. Detroit is installed and all new bearings again. Just need to reinstall the rcv shafts and add gear oil and the front will be done

 

[NickMaul]

I “sent it” as the youngins like to say

Sent from my iPhone using Tapatalk

 

[ramjo]

Figured out the gas tank I Bought off eBay is actually for a 38-39 chevy car ..but I did pick up this edelbrock intake yesterday and get it bolted on. Now on to find a matching single barrel Rochester.....and another gas tank

 

[Willc]

Cleaned it up and took some pics in case I decide to sell it

 

[untchabl]

@Willc is that a 6.0 or 8.1 truck? Looks good.

 

[Willc]

@Willc is that a 6.0 or 8.1 truck? Looks good.

6.0 224K No leaks no cel's . Well taken care of since 05,
BUY IT!

 

[untchabl]

@Willc nice truck but I'm just finishing up a Cummins project truck for myself. Might have been tempted if it was an 8.1 truck.

 

[junkxj]

Wheel bearing replacement on g.f.'s 5th gen 4runner.

I f'ing hate rust more than anything on the planet!!

You know you have wailed on a hub assembly for a while with a bfh when wheel studs you didnt hit fall out.....

 

[McCracken]

Put the flywheel on and used a scotch brite pad to clean off the surface rust . Bolted up the new clutch and pressure plate. Built a cradle for the transmission. Put the bellhousing back on the trans and prepped it for install. Cut the old doubler supports off of the trans crossmember, and rounded it all out by losing my shit on a front caliper rebuild. All in a day's work. Now I'm back in the house ordering another caliper rebuild kit and a new throw out bearing.

btw, if anyone has any neat tips for getting the dust boot on a 1 ton chevy front caliper please enlighten me.

 

[Jody Treadway]

Do you have emory cloth and caliper assembly lube? Sand the bore and the caliper with the Emory cloth, clean and lube the caliper and piston with the lube.
Slide boot over the piston and press down with a block of wood.
Stop halfway through and make a #BTL post.

 

[McCracken]

Yeah that didn't work because that's what I did sans the #BTL post.

 

[Jody Treadway]

Replaced IAC, made the TPS adjustable and got the idle where I want it.
She ret 2 go

 

[Atla]

Bought this:

It's like brand new. Now I need to swap them out and list my old hardware for sale.

 

[josh$$]

The 1st of many needed new parts not on my crawler but on my 1999 jeep grand Cherokee WJ. As you can see the new head light bezzels we in desperate need of replacing. Next will be the front track bar , ball joints, windshield wiper fluid pumps, and new trans filter and seals